Ratermann Manufacturing, Inc. Customer Service 1-800-264-7793 y Fax 1-800-264-7797 y Order Online at Web Store www.rmiorder.com 29H-4 RMI® Parts for LIQUID LEVEL GAUGE KIT RMI® Parts and Installation Instructions for Liquid Level Gauge Kit Taylor-Wharton is a trademark of Taylor-Wharton International, LLC. RMI® Parts are not licensed, approved or sponsored by the trademark owners. WARNING Latex Gloves should be worn at all times when working on Oxygen containers. After the contents of the container have been emptied, it should be allowed to sit empty until the float rod has a chance to warm up. Time can vary from a few days to a week. Always wear protective gloves that are rated for cryogenic temperature when handling the float rod, as it may retain the extremely cold temperature of the cryogenic liquid and can burn exposed skin. It is important to thoroughly read and understand all of the safety and maintenance sections of your product manual. Exposure to cryogenic liquid or low temperature gas can result in injury. Including, severe skin burns and tissue damage. Be sure to follow all safety precautions. Wear proper safety equipment to protect body, hands, and face. Prior to performing any work on a container, be sure to completely remove all liquid and vent pressure. Be absolutely sure that all parts and tools, as well as hands and work area, are completely free of any Grease, Oil, or Dirt. All parts intended for use on liquid cylinders that are exposed to product, must be properly cleaned for Oxygen service. Recommended Gloves for working on parts used in an oxygen clean environment. Part # Description PNG-S Purple Nitrile Gloves – Small PNG-M Purple Nitrile Gloves – Medium PNG-L Purple Nitrile Gloves – Large PNG-XL Purple Nitrile Gloves – Extra Large Purple Nitrile Powder-Free Exam Gloves These Latex-Free gloves will NOT give protection from cold or cryogenic liquids. WARNING: Products in this catalog can expose you to chemicals including lead which is known to the State of California to cause cancer, birth defects or reproductive harm. For more information, go to https://www.p65warnings.ca.gov Model Kit Part Number Snap-On Indicator BC-400, LF-400, TCM-400 LL-RETRO45-9C50 Included (Beverage Carbonation) BC-600, EC-450, EC-550, EC-600, EC-750, TCM-600 LL-RETRO45-9C51 Included (Beverage Carbonation) EC-150, LF-150 LL-RETRO45-9C52 Included (Beverage Carbonation) EC-300, LF-300 LL-RETRO45-9C53 Included (Beverage Carbonation) XL-45, XL-55 (Older 22” O.D.) LL-RETRO45 Order Separately XL-50, XL-55, XL-180 (Current 20” O.D.) LL-RETRO45-9C55 Order Separately XL-65, XL-240 (Current 20” O.D.) LL-RETRO45-9C56 Order Separately XL-70, (XL-160, XL-240 Old Style 26” O.D.) LL-RETRO45-9C57 Order Separately XL-100 LL-RETRO45-9C58 Order Separately XL-60 LL-RETRO45-9C59 Order Separately SNAP-ON INDICATOR Selecting the Proper Kit and Indicator For Liquid Cylinders and Beverage Carbonation Vessels – Taylor-Wharton Style Converts to Snap on Liquid Indicator KIT SELECTION CHART * Kits include: Liquid Level Gauge Cover Gasket Washers and Screws Float Rod (not pictured) Snap on Indicator (if noted below) Kit converts old style to new style Liquid Level Gauge* Service Carbon Dioxide Nitrogen Argon Oxygen Part Number LL-TW-RCD LL-TW-RN LL-TW-RA LL-TW-RO
